Beginner's Plumbing: What You Need for Installing a Bathtub
Beginner's Plumbing: What You Need for Installing a Bathtub
Blog Article
Are you on the lookout for help and advice about A Step-by-Step Guide to Installing a Bathtub?
Mounting a bath tub isn't specifically rocket science, but it does need solid plumbing, carpentry, as well as in some cases, tiling skills. Replacing an old tub with a new one is likewise a moderately tough task. If the old bathtub is easily accessible, the job can move speedily; if you have to open up a wall to remove the old tub as well as position the new tub, the task is a lot harder. In either instance, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and set in the new one. Make sure you have actually certified yourself for the job and fit attempting it. Rather than employing a professional to take over a halfway-completed project, it is much better to consider using one prior to you begin. Possibilities are you may require a specialist plumber to make tube connections.
This post will help you mount a new tub in your washroom if you have currently acquired a brand-new tub as well as do not require to transform the setup of your previous water system pipes.
Your tools and material list ought to make up the following:
Planning for the Installment
Firstly, the supporting frame provided with the bathroom must be fitted (if needed) according to the supplier's directions. Next off, fit the faucets or mixer to the bathtub. When suitable the tap block, it is important to make sure that if the faucet features a plastic washer, it is fitted in between the bathroom and the faucets. On a plastic bathroom, it is also reasonable to fit a supporting plate under the faucets unit to stop pressure on the bathtub.
Fit the versatile faucet adapters to the bottom of the two taps using 2 nuts as well as olives (sometimes supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and after that pass the outlet with the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Take a look at the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipeline to the overflow face which ought to be fitted inside the bathroom. Make certain you use all of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Attach all-time low of the overflow tube in a similar manner.The bathroom need to now be ready to be fitted in its last position.
Removing Old Taps
If you require to replace old taps with new ones as a part of your installment, then the first thing you should do is separate the water. After doing so, switch on the faucets to drain any kind of water staying in the system. The process of getting rid of the existing taps can be fairly troublesome as a result of the limited gain access to that is typically the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the faucets. Have a cloth all set for the continuing to be water that will certainly come from the pipelines. Once the supply pipelines have been removed, utilize the exact same tool to loosen up the nut that holds the faucets onto the bath/basin. You will certainly need to stop the single taps from turning during this procedure. When the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Prior to going on to fit the brand-new faucets, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new taps to fit.
Installing the Bath tub
Utilizing the two wooden boards under its feet, position the tub in the called for position. The wooden boards are handy in evenly spreading out the weight of the bath tub over the area of the boards rather than focusing all the weight onto four small factors.
The next objective is to guarantee that the tub is leveled all round. This can be achieved by inspecting the spirit level and adjusting the feet on the tub till the spirit level reviews level.
To mount faucets, fit all-time low of the outermost versatile faucet port to the appropriate supply pipeline by making a compression join; then do the very same for the various other tap.
Turn on the water supply as well as examine all joints and also new pipework for leakages and also tighten them if required. Fill up the tub and likewise inspect the overflow outlet as well as the normal outlet for leaks.
Ultimately, take care of the bath paneling as described in the supplier's instruction manual. Tiling and also securing around the bathtub must wait until the tub has been utilized a minimum of once as this will resolve it right into its final placement.
Suitable New Touches
If the tails of the new faucets are plastic, then you will require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the faucet as well as the other end gives a link to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly need decreasing couplers, which connects the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washing machines are in location between the faucet and also the sink. Secure the faucet in position with the manufacturer given backnut. When the faucet is safely in position, the supply pipes can be connected to the tails of the taps. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous type needs to be linked to the faucet ends first, tightening up only by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bath tub
In the location where the bath satisfies the tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate sufficient to crack a rigid seal, causing the water to penetrate the wall between the bathroom and also the tiling, bring about difficulties with moisture as well as feasible leaks to the ceiling below.
You can choose from a range of coloured sealants to blend in your fixtures and fittings. They are offered in tubes as well as cartridges, and also can securing voids approximately a width of 3mm (1/8 inch). If you have a bigger void to load, you can load it with twists of drenched paper or soft rope. Remember to constantly load the bath tub with water prior to sealing, to enable the motion experienced when the bathtub is in usage. The sealer can split rather early if you do not consider this activity before securing.
Additionally, ceramic coving or quadrant ceramic tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally easily readily available on the marketplace. It is a good idea to fit the ceramic tiles making use of water-resistant or water-proof adhesive and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I have been very fascinated with Installing A Bathtub and I hope you enjoyed reading the entry. For those who enjoyed our page kindly do not forget to pass it around. I cherish reading our article about How to Install a Bathtub Yourself.
Additional Resources Report this page